How Much Does Fence Installation Cost in Kent, WA?
Regional fence installation pricing covering Kent, WA: a 6-ft cedar privacy fence runs $35–$55 per linear foot installed, about $5,250–$8,250 for a typical 150-foot yard. These are South Puget Sound / Seattle-metro rates rather than a city-verified Kent bid, so use the calculator for a number tied to your own lot.
Last updated:
Fence Installation in Kent, WA typically costs $35–$55 per linear foot in 2026, depending on property size and job conditions. Most Kent property owners pay the mid-range tier. Get an exact, itemized price for your address in under 60 seconds with an instant Quotly quote.

In Kent, fencing a yard almost always means cedar. A 6-foot cedar privacy fence is the default on both sides of the Green River Valley: it shrugs off wet Puget Sound winters, takes stain well, and looks at home next to the Douglas firs behind half the lots in town. Regionally that fence runs $35–$55 per linear foot installed, so a standard 150-foot suburban perimeter lands around $5,250–$8,250 before gates, old-fence removal, or permits. Vinyl and chain link are priced off their own separate bands, broken out below. The figures on this page are South Puget Sound / Seattle-metro regional rates, not a city-verified Kent bid. Kent's roughly 133,000 residents draw from the same King County contractor pool as Renton, Auburn, Federal Way, and Covington, so quotes tend to land in a similar range, but what actually moves your price is local. A flat valley-floor lot near Kent Station digs fast; a sloped run above the valley or a rocky stretch out toward Clark Lake Park adds labor and hours. Kent's 10.4% sales tax goes on top of the job, and if the crew needs to stage lumber or park equipment on the sidewalk or planting strip, KCC 6.07.030 requires a street use permit before they do. Run the calculator to turn these ranges into a number for your yard.
2026 Fence Installation Prices in Kent
| Fence Type | Price per Foot | Typical Total |
|---|---|---|
| 6-ft cedar privacy: the Kent default | $35–$55 / linear foot installed | $5,250–$8,250 for a 150-ft yard |
| 6-ft vinyl privacy (tongue-and-groove $40–$55 · lattice-top $50–$65 · premium wood-grain $60–$85) | $40–$85 / linear foot installed | $6,000–$12,750 for a 150-ft yard |
| 6-ft chain link, galvanized | $22–$32 / linear foot installed | $3,300–$4,800 for a 150-ft yard |
| 6-ft chain link, black vinyl-coated | $28–$38 / linear foot installed | $4,200–$5,700 for a 150-ft yard |
| Common add-ons (additive) | Gates $150–$1,600 · old-fence removal $3–$7/lf · permit $100–$500 | Not included in the per-foot rates above |
Prices reflect 2026 rates from verified contractors serving the 98030, 98031, 98032, 98042, 98064 ZIP code area. Need an exact number? Get an instant Kent fence installation quote based on your actual property.
Sample Quote for a Typical Kent Property
Sample quote based on a typical Kent property. Your actual price may vary: get your own Kent fence installation quote in 60 seconds.
What's Included in a Standard Kent Fence Installation Service
A fence installation quote through Quotly is priced end-to-end, so the per-foot rate covers the real work rather than materials dropped in your driveway. A standard 6-ft cedar privacy install in Kent includes:
- On-site measurement and layout: walking the line, marking corners, and setting gate openings
- A free 811 utility locate before any post hole is dug
- Digging post holes and setting posts in concrete to depths that hold in valley-floor soil
- Installing rails, pickets, and cap or trim boards for a full 6-ft privacy panel
- Hanging gates with heavy-duty hinges, latches, and a drop rod on doubles
- Scrap haul-away and daily job-site cleanup, including sweeping the sidewalk and planting strip
Compare Fence Installation Companies in Kent: Pricing Models
Material drives most of the price. Each material, and each sub-tier within it, carries its own installed band, so here is how the common Kent options actually compare on a standard residential run:
| Pricing Model | Typical Price | Best For | Trade-offs |
|---|---|---|---|
| Cedar, 6-ft privacy (standard) | $35–$55 / lf installed | Full backyard privacy with a warm, natural look; the default across South King County | Wants a stain or seal every few years to hold its color through wet winters |
| Cedar, horizontal/designer | up to about $110 / lf installed | Modern street-facing runs where the fence is part of the curb appeal | Roughly double a standard cedar privacy fence; tighter tolerances mean more labor |
| Vinyl privacy, tongue-and-groove (6 ft) | $40–$55 / lf installed | Homeowners who never want to stain a fence again and are fine with a plain white panel | Higher up-front cost than standard cedar; panels can't be refinished if scuffed |
| Vinyl privacy, lattice-top (6 ft) | $50–$65 / lf installed | Softening a tall solid run with some light and airflow at the top | Costs more than plain tongue-and-groove and the lattice collects moss in shaded yards |
| Vinyl privacy, premium/wood-grain (6 ft) | $60–$85 / lf installed | A cedar look with vinyl maintenance: the top of the vinyl range | The most expensive vinyl tier; still tops out below designer horizontal cedar |
| Chain link, galvanized (6 ft) | $22–$32 / lf installed | Budget enclosures, pet runs, and side yards where privacy isn't the goal | No privacy and a utilitarian look; bare galvanized steel shows against green yards |
| Chain link, black vinyl-coated (6 ft) | $28–$38 / lf installed | The same budget enclosure but visually recessive: black mesh reads as almost invisible against trees | Costs more per foot than galvanized; coating can chip at cut ends over time |
How to Save Money on Fence Installation in Kent
Fence only the runs that actually need privacy
Privacy-fencing the two side yards and the back while leaving the street frontage open or low cuts linear footage directly. Every foot you skip saves $35–$55 at the cedar rate.
Split the boundary run with your neighbor
A shared property-line fence is commonly split 50/50, which halves your cost on that run. Agree on the line off a survey or existing pins before the crew sets posts, so nobody pays to move it later.
Reuse posts that are still sound
If the existing fence has solid concrete-set posts, some crews can re-skin the panels instead of tearing everything out. That avoids the $3–$7 per foot removal add-on plus most of the post-setting labor.
Install outside the summer rush
Kent crews are busiest from June through September once the valley dries out. Getting quotes in the wet months and installing in a March–May or October shoulder window can win a better rate and a faster start.
Bundle gates into the original install
A single walk gate runs $150–$300 when it goes in with the fence, versus a separate trip charge afterward. The same logic applies to a $1,100–$1,600 drive gate. Decide before the crew mobilizes.
Kent Service Area by ZIP Code
| ZIP | Neighborhoods Covered |
|---|---|
| 98030 | Central and east Kent around Kent Station and the accesso ShoWare Center, plus the slopes rising toward Mill Creek Canyon Earthworks Park |
| 98031 | East of the valley floor along the SR 515 / Benson Road corridor and the residential streets running toward Panther Lake |
| 98032 | West Kent and the Green River Valley, including lots along the Green River Trail and the hillside above the valley west of SR 167 |
| 98042 | Southeast Kent toward Lake Meridian, Clark Lake Park, and the Kent-Kangley Road (SR 516) corridor |
| 98064 | Kent postal coverage; crews serve properties across the full city limits and the adjacent unincorporated King County pockets |
Local Regulations & HOA Notes for Kent Fence Installation
Fence work in Kent runs into three city rules worth knowing before the crew shows up. The notes below quote the Kent City Code directly where a citation exists; anything about fence height or setbacks is set by the city and should be confirmed with the City of Kent for your specific lot.
- Work hours and noise: Kent regulates noise by decibel limits under its EDNA zone standards in Chapter 8.05 KCC, and KCC 8.05.110 layers a fixed-hours exemption on top of them. Both apply at once: 'Sounds originating from residential property related to temporary projects for the maintenance or repair of homes, grounds and appurtenances are exempt from the maximum permissible noise levels during the hours of 7:00 a.m. to 10:00 p.m.' That 7:00 AM – 10:00 PM window is the same on weekdays, Saturday, and Sunday, so an auger or post-hole digger is fine inside it and back under the decibel caps outside it.
- Staging in the right-of-way: KCC 6.07.030 states that 'it shall be unlawful for anyone to use any public place for private purposes without having first obtained a street use permit from the director.' KCC 6.07.020 defines a 'public place' to include streets, sidewalks, and planting (parking) strips, and defines 'use' to include storing or placing material, equipment, staging, or machinery there. If your installer plans to stack cedar panels on the planting strip, park a dumpster at the curb, or block the sidewalk with a mixer, that permit comes first.
- Fence height, setbacks, and permits: height limits are typically lower in front yards than in back, and corner lots carry sight-triangle rules that keep fences low near the intersection. A permit adds $100–$500 when one is required; confirm current requirements with the City of Kent before you build, and call 811 for a free utility locate before any digging.
- Property lines: pull a survey or find the existing pins before posts go in. A fence set even a foot over the line is a rebuild at your cost, and a written agreement with the neighbor on a shared run avoids the argument entirely.
Kent Fence Installation Calendar
What to expect month-by-month for fence installation in the Kent, WA climate.
| Month | Recommended Activity |
|---|---|
| January | Wet winter ground makes post-digging slow, so most Kent homeowners spend January gathering quotes rather than installing. |
| February | Still the wettest stretch of the year: a good month to lock in a spring start date before crews fill up. |
| March | Growing season opens and the last spring frost lands around March 2, so early installs start moving as the ground firms. |
| April | Soil dries enough for clean post holes and demand climbs; book a few weeks out. |
| May | Prime fence weather arrives: dry, workable soil makes concrete-set posts fast. |
| June | Peak season begins and Kent crews are at their busiest, so expect longer lead times. |
| July | Dry summer conditions are ideal for long cedar runs and dead-straight lines. |
| August | Still peak building weather, with the fullest crew schedules of the year. |
| September | Warm, dry days continue while demand eases: the smartest shoulder-season window. |
| October | Rain returns and the ground softens; finish installs before the wet season sets in. |
| November | Growing season closes and the first fall frost lands around November 23, slowing digging further. |
| December | Off-season quoting month: line up an early-year install while schedules are calm. |
What Affects Fence Installation Cost in Kent?
Material and grade
Cedar anchors the Puget Sound market at $35–$55 per linear foot installed, with horizontal/designer cedar running up to about $110/lf. Vinyl and chain link are priced off their own separate bands (see the comparison table), so never apply the cedar rate to another material.
Fence length
You pay by the linear foot, so total perimeter is the single biggest lever. A standard suburban Kent run is 100–200 feet; exactly 150 feet of 6-ft cedar with no add-ons is the $5,250–$8,250 figure quoted throughout this page.
Gates
Gates are additive on top of the per-foot rate. A single walk gate runs $150–$300 ($400–$600 in vinyl), a double gate is $400–$900, and a single drive gate wide enough for a vehicle is $1,100–$1,600.
Old-fence removal
Tearing out and hauling away an existing fence is a separate line item at $3–$7 per linear foot, billed on top of the new-install rate. On a 150-foot run that is roughly $450–$1,050 before the new fence is priced at all.
Terrain, soil, and access
The Green River Valley floor digs easily; the slopes on either side, glacial till, and buried rock all add labor, as do stepped panels on a grade. Tight side-yard access that forces material to be carried by hand instead of wheeled in adds hours to the same footage.
Permits and right-of-way
A building permit adds $100–$500 when your fence height or location requires one. Separately, KCC 6.07.030 requires a street use permit before a crew stores materials or equipment on a Kent sidewalk, street, or planting strip. Budget for both if your lot has no on-site staging room.
Frequently Asked Questions
How much does a fence cost in Kent, WA?
Why is cedar the standard fence material around Kent?
How much do gates add to a fence quote?
What does it cost to remove my old fence first?
Is chain link much cheaper than cedar?
Do I need a permit to build a fence in Kent?
What hours can a fence crew work in Kent?
Are these verified Kent contractor rates?
Who offers fence installation near me in Kent, WA?
Nearby areas
See fence installation costs in Des Moines, Covington, Federal Way, and Maple Valley.
Other services in Kent
Get pricing for Lawn Mowing Cost, Pressure Washing Cost, Gutter Cleaning Cost, House Cleaning Cost, Junk Removal Cost, Window Cleaning Cost, Dog Waste Removal Cost, Driveway Installation Cost, Carpet Cleaning Cost, and Gutter Installation Cost in Kent, WA.