How Much Does Gutter Installation Cost in Kent, WA?
Gutter installation in Kent, WA runs $1,400 to $2,800 for a typical 150 to 200 foot whole-house job in seamless aluminum, about $7 to $14 per linear foot installed, before Kent's 10.4% sales tax.
Gutter Installation in Kent, WA typically costs $1,400 to $2,800 per visit in 2026, depending on property size and job conditions. Most Kent property owners pay the mid-range tier. Get an exact, itemized price for your address in under 60 seconds with an instant Quotly quote.
Kent is Washington's sixth-largest city and King County's third, home to about 133,000 people spread from the flat Green River Valley floor around Downtown Kent and Kent Station up onto East Hill, West Hill, Scenic Hill and the Lake Meridian area. Roughly 39 inches of rain a year (NOAA 1991 to 2020 normals, Seattle-Tacoma Intl Airport station) means a gutter system here is not decoration: it is what keeps water off your fascia, siding and foundation from fall through spring. A standard Kent replacement is seamless aluminum K-style gutter in 5 or 6 inch, priced per linear foot at about $7 to $14 installed with standard downspouts usually bundled. On the 150 to 200 feet a typical whole house carries, that lands at $1,400 to $2,800 before tax. These numbers are a Seattle-metro and South King County regional baseline, not a survey of Kent installer invoices, so treat them as a fair-price check rather than a guaranteed bid. Below: price tiers by footage, an itemized sample quote with Kent's 10.4% sales tax broken out, a material-by-material comparison from vinyl to copper, five ways to keep the bill down, the Kent City Code sections that actually touch a gutter job, and a month-by-month calendar for planning the install around the wet season. Pricing a job across the line? See our gutter installation guides for Renton, Auburn, Covington, Federal Way and Maple Valley.
2026 Gutter Installation Prices in Kent
| Lot Size | Per Visit | Monthly (4×) |
|---|---|---|
| Smaller home, about 150 linear feet, seamless aluminum (5 or 6 inch) | $1,050 to $2,100 installed | One-time install at $7 to $14 per linear foot |
| Mid-size home, about 175 linear feet, seamless aluminum (5 or 6 inch) | $1,225 to $2,450 installed | One-time install at $7 to $14 per linear foot |
| Larger home, about 200 linear feet, seamless aluminum (5 or 6 inch) | $1,400 to $2,800 installed | One-time install at $7 to $14 per linear foot |
| About 200 linear feet, seamless aluminum plus mesh or micro-mesh guards | $2,200 to $5,000 installed | One-time install at $11 to $25 per linear foot (gutter $7 to $14 plus guards $4 to $11) |
Prices reflect 2026 rates from verified contractors serving the 98030, 98031, 98032, 98042, 98064 ZIP code area. Need an exact number? Get an instant Kent gutter installation quote based on your actual lot.
Real Quote Example from Kent
Sample quote based on a typical Kent property. Your actual price may vary: get your own Kent gutter installation quote in 60 seconds.
What's Included in a Standard Kent Gutter Installation Service
A complete Kent gutter installation bid should spell out each of these. If one is missing, ask before you sign, because the gaps are where final invoices grow.
- Measured linear footage for every run, so you can check the bid against the $7 to $14 per foot seamless aluminum range
- Gutter material, profile, size and gauge in writing: for example seamless aluminum K-style, 5 or 6 inch, .027 or .032
- Standard downspouts, which are usually bundled into the per-foot price; any extra or oversized 3x4 downspouts listed separately per unit
- Hangers, end caps, outlets and sealing, with the slope toward each downspout set so water does not stand in the trough
- Tear-off and haul-away of the old gutters on a replacement job: often bundled, but it varies, so confirm it is on the bid. Hauled scrap from Kent generally goes to King County's Bow Lake Recycling & Transfer Station at 18800 Orillia Rd S, Tukwila.
- A note on fascia condition found at tear-off, with any rotted fascia repair quoted per linear foot before the crew replaces it
- Sales tax shown as its own line at Kent's 10.4% rate instead of folded into the base price
Compare Gutter Installation Companies in Kent: Pricing Models
Gutter installation is priced per linear foot, and the material you pick moves that rate more than anything else. Here is how the common options compare, using regional per-foot installed prices.
| Pricing Model | Typical Price | Best For | Trade-offs |
|---|---|---|---|
| Vinyl | About $5 to $8.50 per linear foot | Tight budgets, sheds and small single-story runs | Lowest price, but sold in sections with seams rather than formed seamless on site, and fewer local crews install it. |
| Seamless aluminum K-style (5 or 6 inch) | About $7 to $14 per linear foot | Most Kent homes; this is the standard residential job | Formed on site to your exact run lengths. A 6 inch size adds about $1 to $3 per foot, and heavier .032 gauge adds about $4 to $7 per foot over .027. |
| Galvanized steel | About $11 to $16 per linear foot | Homeowners who want a stiffer gutter that resists denting | Costs more than aluminum and is heavier to hang; ask the installer how they finish cut edges and seams. |
| Copper | About $25 to $50 per linear foot | Historic or high-end homes where the gutter is part of the look | Two to four times the price of aluminum, so a 150 foot house runs $3,750 to $7,500 before tax. |
| Add-on: mesh or micro-mesh guards | About $4 to $11 per linear foot on top of the gutter | Runs directly under trees that shed onto the roof | Adds real money across a whole house; many homeowners guard only the runs under canopy. |
How to Save Money on Gutter Installation in Kent
Measure your rooflines before the first bid
Most whole-house jobs are 150 to 200 linear feet, and seamless aluminum installs at about $7 to $14 per foot. Pace off your eaves and you will know within a few hundred dollars whether a quote is fair.
Buy the size and gauge your roof needs, not the upgrade
Going from 5 inch to 6 inch adds about $1 to $3 per foot, and .032 gauge adds about $4 to $7 per foot over .027. Ask the installer which runs actually need the upgrade instead of applying it to the whole house.
Guard only the runs under trees
Mesh and micro-mesh guards add about $4 to $11 per linear foot, which can nearly double a whole-house job. Guarding just the shaded side, as in the sample quote, keeps that line in the low hundreds.
Get tear-off and haul-away in writing
Removing and hauling the old gutters is often bundled into a Kent replacement price, but not always. Make sure it appears on the bid so it does not show up as a surprise line on the invoice.
Ask for fascia repair as a per-foot price up front
Rotted fascia only shows up once the old gutters come down, and it is billed per linear foot. Agreeing on that rate before work starts keeps a soft board from turning into an open-ended charge.
Kent Service Area by ZIP Code
| ZIP | Neighborhoods Covered |
|---|---|
| 98030 | Scenic Hill, Mill Creek and the west-facing East Hill blocks. This is hill terrain rather than valley floor, so ladder setup on sloped ground can add time to an install. |
| 98031 | The East Hill core above the valley, plus Panther Lake and Garrison Creek. |
| 98032 | The Green River Valley floor and West Hill: Downtown Kent, Kent Station, North Park, Kent Valley, Riverview and Midway. The flat ZIP, where sloped-ground setup generally is not a factor. |
| 98042 | East Hill-Meridian and the Lake Meridian area, running toward Covington. |
| 98064 | A PO-box and business-delivery ZIP only, with no street addresses or homes of its own. Quote your install under your home's street ZIP: 98030, 98031, 98032 or 98042. |
Local Regulations & HOA Notes for Kent Gutter Installation
Four Kent-specific rules worth knowing before a gutter crew shows up:
- Work hours: KCC 8.05.110 (Kent City Code, not King County Code): Kent's general noise standard is decibel-based, with EDNA zone limits under Chapter 8.05, and on top of that residential maintenance and repair work gets a fixed-hours exemption. The code reads: "Sounds originating from residential property related to temporary projects for the maintenance or repair of homes, grounds and appurtenances are exempt from the maximum permissible noise levels during the hours of 7:00 a.m. to 10:00 p.m." That window is 7:00 AM to 10:00 PM every day, Saturday and Sunday included, so a weekend install with a gutter-forming machine running is fine during those hours.
- Sales tax: 10.4% on the invoice: Kent's combined sales tax rate is 10.4% as of 2026 Q2, and Kent sits inside the RTA transit district, which is part of why the rate runs this high. Add it on top of any pre-tax price on this page: the sample quote's $1,770.00 subtotal becomes $1,954.08.
- Street use permit if the crew stages in the right-of-way: KCC 6.07.030 makes it unlawful "to use any public place for private purposes without having first obtained a street use permit," and KCC 6.07.020 defines public places to include streets, sidewalks and planting (parking) strips, with use covering placement of scaffold, material, machinery or tools. If the gutter truck, forming machine or ladders have to sit on the sidewalk or planting strip, settle in writing who pulls the permit; work staged entirely on your own property does not trigger it.
- Kent business license for the installer: Under KCC 5.01.040, businesses working in Kent need a City of Kent business license, issued directly by the City of Kent Finance Department (Kent is not a state BLS partner city), with a Washington UBI number required first. It is a fair question to ask any installer before you sign.
Gutter Installation in Kent: Neighborhoods We Cover
Verified contractors on Quotly serve gutter installation customers across Kent and surrounding King County neighborhoods, including:
Kent Gutter Installation Calendar
What to expect month-by-month for gutter installation in the Kent, WA climate.
| Month | Recommended Activity |
|---|---|
| January | Peak of the wet season: watch your old gutters during a downpour and note every spot that overflows or drips behind the fascia. |
| February | Measure your rooflines and collect bids now, while you can still see exactly where water is going. |
| March | Last spring frost lands around March 2 and the growing season opens, a reasonable start to install season. |
| April | Book your install date and confirm material, size, gauge and tear-off in writing. |
| May | Longer dry spells make it easier to inspect and replace any rotted fascia when the old gutters come down. |
| June | Summer is the most comfortable stretch for a full tear-off and replacement, with less rain to work around. |
| July | A good month to add guards only on the runs that sit under trees. |
| August | Get any remaining install on the calendar before fall, when Kent's rainy season returns. |
| September | Last comfortable window to finish a replacement before steady fall rain. |
| October | Run a hose down each new downspout to confirm water discharges away from the foundation. |
| November | First fall frost arrives around November 23 and the growing season closes, so check hangers and seams on the new system after the first heavy storms. |
| December | Note any run that still overflows in winter storms so it can be resized or given an extra downspout next season. |
What Affects Gutter Installation Cost in Kent?
Linear footage, the main cost driver
Gutter installation is priced per foot, and a typical whole house carries 150 to 200 linear feet. Wraparound porches, dormers and a detached garage add footage and push a bid toward the top of the $1,400 to $2,800 range.
Material
Vinyl runs about $5 to $8.50 per foot, seamless aluminum $7 to $14 (the standard), galvanized steel $11 to $16, and copper $25 to $50. Material choice can move a 175 foot job by thousands of dollars.
Size and gauge
A 6 inch gutter runs about $1 to $3 more per foot than 5 inch, and thicker .032 aluminum adds about $4 to $7 per foot over .027. Ask the installer to explain which size and gauge your roof needs.
Gutter guards
Mesh and micro-mesh guards add about $4 to $11 per linear foot on top of the gutter itself. Guarding the full house versus only the runs under trees is one of the biggest swings on a Kent bid.
Downspouts
Standard downspouts are usually bundled into the per-foot price. Extra downspouts, or oversized 3x4 downspouts for long runs, are priced per unit, so get them itemized.
Stories, access, tear-off and fascia
Two-story and steep sites take more setup time, as do sloped lots on Kent's hills; the premium varies, so get a quote. Removing old gutters and repairing rotted fascia are also variable lines that should be priced in writing.
Frequently Asked Questions
How much does gutter installation cost in Kent, WA?
Are these Kent-specific prices?
What size gutter does a Kent home need, 5 inch or 6 inch?
Is sales tax added to a gutter installation quote in Kent?
Do gutter guards make sense in Kent?
Does the price include removing my old gutters?
Can the crew work on a Saturday or Sunday in Kent?
Does my installer need a permit to park equipment on the street?
Who offers gutter installation near me in Kent, WA?
Nearby areas
See gutter installation costs in Renton, Auburn, Covington, Federal Way, and Maple Valley.
Other services in Kent
Get pricing for Lawn Mowing Cost, Pressure Washing Cost, Gutter Cleaning Cost, House Cleaning Cost, Junk Removal Cost, Window Cleaning Cost, Fence Installation Cost, Dog Waste Removal Cost, Driveway Installation Cost, and Carpet Cleaning Cost in Kent, WA.